pico Talon
$24.99
Pico Talon – Compact, Stable 3D Printed FPV Aircraft Designed for Everyday Missions.
| Wingspan | 905mm |
|---|---|
| Length | 640mm |
| AUW | 650-1100g |
| Optimal Speed | 50-70 km/h |
| Bed Size | min. 200x200mm |
| Material | LW-PLA + PETG |
CHECK ALSO
OVERVIEW
General Data
The Pico Talon is a compact and practical UAV platform featuring a classic pusher layout and V-tail. Its lightweight hybrid airframe, optimized for 3D printing and reinforced with carbon tubes, provides stable flight performance while keeping the aircraft easy to transport, store, and deploy. A modular, replaceable nose section allows quick adaptation for different FPV setups, cameras and sensors, making the Pico Talon a versatile choice for everyday flying and compact mission profiles.
Check assembly manual, full list of needed accessories and more tips here:
STEP FILES
STEP files of important parts provided for easy customization. Modify and adapt components effortlessly to suit your unique requirements. Check the full list of files in the user manual.
WINGTIP OPTIONS
Two wingtip variants are included: upward-curved and downward-curved, allowing you to choose the preferred look.
GALLERY
VIDEOS
CFD RESULTS
The aircraft’s geometry is optimized for high aerodynamic efficiency and stable flight. Its streamlined airframe provides balanced lift distribution while reducing drag. Based on the Selig S3021 airfoil, the aircraft remains longitudinally stable with a properly set center of gravity and produces almost no pitching moment at 0° angle of attack. Peak efficiency is achieved between 0° and 3°, matching typical cruise conditions.
WIRING DIAGRAM
A simplified sample wiring diagram for easier understanding of component layout and connections. Also available in PDF within the file package.
Required accessories:
| ITEM | QUANTITY |
| 8x500mm Carbon Tube (MAIN SPAR) link / link / link | 1 |
| 6x500mm Carbon Tube (SECONDARY SPAR) link / link / link | 1 |
| 3x250mm Carbon Tube (WING SPAR) link / link / link | 2 |
| 3x250mm Carbon Tube (AILERON HINGE) link / link / link | 2 |
| 6x170mm Carbon Tube (V TAIL SPAR) link / link / link | 2 |
| 3x170mm Carbon Tube(RUDDER HINGE) link / link / link | 2 |
| Thick CA Glue link | 1-2 Tubes |
| CA Activator link | 1 |
| M3 Threaded Insert (Outer Ø5mm, height 5mm) link | 19 |
| M3x6mm Screw | 12 |
| M3x10mm Screw | 13 |
| M3x20mm Screw | 2 |
| M3x25mm Screw | 2 |
| Hot Glue (optional) link | Small amount |
| Epoxy Glue (optional) link | Small amount |
| LW-PLA / LW-ASA link / link / link | 1 roll |
| PC / PETG / other rigid material link / link | Small amount |
| Velcro Strap link | 2 |
| Servo Extension Cable link | 2 |
| Control Horn link | 4 |
| Pushrod link / link | 4 |
Recommended electronics:
| Motor | 2207 Motor e.g. T-Motor F60 1750KV link |
| Propeller | 5-7 inch Propeller link / link |
| Flight Controller | Speedybee F405 Wing or any other Mavlink FC link |
| GPS | Matek M10Q or similar GPS with compass link |
| Servos | 4x EMAX ES08 MAII Metal Gear or similar link |
| ESC | 20-40A link / link |
| Battery | 4S-6S Li-Ion / Li-Po link / link |
| Receiver | Matek R24-D ELRS or similar link |
| FPV Camera + VTX | Walksnail Avatar or any Digital or Analog VTX link / link |
| FPV Goggles | Walksnail Goggles X or any other matching the chosen VTX link |
Required Additional Equipment:
| 3D Printer | Bambu Lab X1C or other with min. 220x220x200mm build volume link |
| RC Transmitter | Radiomaster TX16S or other modern RC Transmitter link |
| Transmitter Module | HappyModel ES24TX or other ELRS TX link |
Printing Settings:
Check the specified print settings on the Print Settings Page
Licensed for personal use only under: License Agreement
RELATED PRODUCTS